TrueScaleAudio

Compare speakers at true scale

Pick two speakers and see them side by side at their real-world size.

Speaker A

Stands apply to bookshelves only

Speaker B

Stands apply to bookshelves only

References

Front view — side by side at true scale

ADynaudio Confidence 50BKlipsch RP-6000F II
Dynaudio Confidence 50 front view
Klipsch RP-6000F II front view

Click either cabinet to swap A ↔ B · Reference height: 1557 mm (155.7 cm) · 1 mm = 0.36 px

Plan view — footprint at true scale

front wall
A1543 cm²364 mm424 mm
B1075 cm²241 mm446 mm
0 mm100 mm30 mm

A shelf applies to bookshelf speakers only — one of these stands on the floor.

Seen from above, both pushed back to the same front wall — the wall behind the speakers. Only height, width and depth are published, so each cabinet is drawn as a rectangle: this is the surface a speaker reserves, not its exact outline. A curved or tapered cabinet takes a little less. How far a speaker should sit from the wall is yours to set: makers rarely publish it, and the ones that do disagree by design.

Performance — where each one sits in the catalog

BassTrebleSensitivityEasy loadCone area
Bass reachTreble reachSensitivityEasy loadCone area
Confidence 5035 Hz22 kHz87 dB4 Ω869 cm²
RP-6000F II38 Hz25 kHz96 dB8 Ω433 cm²
Median32 Hz30 kHz90 dB6 Ω654 cm²
How to read this chart

Each axis spans the range the 648 floorstanders in the catalog actually cover, so equal distance means equal difference — and for cone area and the two frequencies, which are read as ratios, equal distance means equal ratio. The dashed inner ring is where the scale starts, not zero. Ranked within a class because a bookshelf measured against floorstanders is feeble on every axis for the single reason that it is a bookshelf. Cone area is summed from the drive units — no maker publishes it. Bass and treble reach are quoted to different tolerances and only 56% of the catalog says which, so read those two axes as approximate. The grey outline is the median of the pair's own class, the 600 passive floorstanders — same type, same side of the active/passive line, which matters because the two halves are not the same product: the median active bookshelf carries 155 cm² of cone against the passive median's 219. Median rather than mean, because a handful of very large cabinets would drag a mean above most of the class it claims to describe.

Dynaudio Confidence 50vsKlipsch RP-6000F II

The Dynaudio Confidence 50 stands 155.7 cm tall — about 55.1 cm more than the Klipsch RP-6000F II at 100.6 cm. On footprint the Dynaudio Confidence 50 is the wider cabinet (36.4 cm versus 24.1 cm). At 96 dB against 87 dB, the Klipsch RP-6000F II is the easier load to drive and plays louder from the same amplifier. The Dynaudio Confidence 50 reaches deeper in the bass, down to 35 Hz versus 38 Hz. Low frequencies come from a 180 mm cone on the Dynaudio Confidence 50 and a 165 mm cone on the Klipsch RP-6000F II. On price, the Dynaudio Confidence 50 sits higher — about $30,000 a pair against $449 for the Klipsch RP-6000F II.

Specifications

AB
ManufacturerDynaudioKlipsch
ModelConfidence 50RP-6000F II
HiFi ladder position#597 of 648 floorstander#157 of 648 floorstander
Height1557 mm1006 mm
Width364 mm241 mm
Depth424 mm446 mm
Footprint1543 cm²1075 cm²
Space taken240.3 L108.1 L
Weight49.6 kg22.4 kg
Enclosurebass-reflex-downbass-reflex-rear
Drivers1× 28 mm tweeter (Esotar 3 soft dome with DDC Lens), 2× 150 mm midrange (MSP with Horizon Surround), 2× 180 mm woofer (NeoTec MSP cone)1× 25 mm tweeter (titanium LTS dome), 2× 165 mm woofer (Cerametallic cone)
Crossover frequency200 / 2860 Hz1770 Hz
Frequency — low35 Hz38 Hz
Frequency — high22000 Hz25000 Hz
Sensitivity87 dB96 dB
Impedance4 Ω8 Ω
Recommended amp——
MAP (USD)$30,000 / pair$449 each
Where to buyCheck availability ↗Check on Amazon ↗
Brand websitedynaudio.com ↗klipsch.com ↗
Product pageOpen product page ↗Open product page ↗

Larger value highlighted in green. For low-frequency extension, lower Hz = greater bass reach, so the deeper side is highlighted.