TrueScaleAudio

Compare speakers at true scale

Pick two speakers and see them side by side at their real-world size.

Speaker A
Speaker B
References

Front view — side by side at true scale

AKEF Q1 MetaBKlipsch RP-500M II
KEF Q1 Meta front view
Klipsch RP-500M II front view

Click either cabinet to swap A ↔ B · Reference height: 344 mm (34.4 cm) · 1 mm = 1.63 px

Plan view — footprint at true scale

front wall
A499 cm²180 mm277 mm
B462 cm²171 mm270 mm
0 mm100 mm30 mm
150 mm500 mm300 mm

Seen from above, both pushed back to the same front wall — the wall behind the speakers. Only height, width and depth are published, so each cabinet is drawn as a rectangle: this is the surface a speaker reserves, not its exact outline. A curved or tapered cabinet takes a little less. How far a speaker should sit from the wall is yours to set: makers rarely publish it, and the ones that do disagree by design.

Performance — where each one sits in the catalog

BassTrebleSensitivityEasy loadCone area
Bass reachTreble reachSensitivityEasy loadCone area
Q1 Meta51 Hz20 kHz86 dB4 Ω138 cm²
RP-500M II50 Hz25 kHz92 dB8 Ω144 cm²
Median45 Hz25 kHz87 dB6 Ω219 cm²
How to read this chart

Each axis spans the range the 470 bookshelves in the catalog actually cover, so equal distance means equal difference — and for cone area and the two frequencies, which are read as ratios, equal distance means equal ratio. The dashed inner ring is where the scale starts, not zero. Ranked within a class because a bookshelf measured against floorstanders is feeble on every axis for the single reason that it is a bookshelf. Cone area is summed from the drive units — no maker publishes it. Bass and treble reach are quoted to different tolerances and only 56% of the catalog says which, so read those two axes as approximate. The grey outline is the median of the pair's own class, the 385 passive bookshelves — same type, same side of the active/passive line, which matters because the two halves are not the same product: the median active bookshelf carries 155 cm² of cone against the passive median's 219. Median rather than mean, because a handful of very large cabinets would drag a mean above most of the class it claims to describe.

KEF Q1 MetavsKlipsch RP-500M II

The Klipsch RP-500M II stands 34.4 cm tall — about 4.2 cm more than the KEF Q1 Meta at 30.2 cm. At 92 dB against 86 dB, the Klipsch RP-500M II is the easier load to drive and plays louder from the same amplifier. On price, the KEF Q1 Meta sits higher — about $749 a pair against $549 for the Klipsch RP-500M II.

Specifications

AB
ManufacturerKEFKlipsch
ModelQ1 MetaRP-500M II
HiFi ladder position#101 of 470 bookshelf#193 of 470 bookshelf
Height302 mm344 mm
Width180 mm171 mm
Depth277 mm270 mm
Footprint499 cm²462 cm²
Space taken15.1 L15.9 L
Weight6.1 kg5.95 kg
Enclosurebass-reflex-rearbass-reflex-rear
Drivers1× 25 mm tweeter (MAT aluminium dome), 1× 130 mm mid-bass (aluminium cone)1× 25 mm tweeter (titanium LTS dome), 1× 133 mm mid-bass (Cerametallic cone)
Crossover frequency2100 Hz1530 Hz
Frequency — low51 Hz50 Hz
Frequency — high20000 Hz25000 Hz
Sensitivity86 dB92 dB
Impedance4 Ω8 Ω
Recommended amp10–150 W—
MAP (USD)$749 / pair$549 / pair
Where to buyCheck on Amazon ↗Check on Amazon ↗
Brand websiteinternational.kef.com ↗klipsch.com ↗
Product pageOpen product page ↗Open product page ↗

Larger value highlighted in green. For low-frequency extension, lower Hz = greater bass reach, so the deeper side is highlighted.