TrueScaleAudio

Compare speakers at true scale

Pick two speakers and see them side by side at their real-world size.

Speaker A

Stands apply to bookshelves only

Speaker B

Stands apply to bookshelves only

References

Front view — side by side at true scale

AKEF Reference 5 MetaBKlipsch La Scala AL6
KEF Reference 5 Meta front view
Klipsch La Scala AL6 front view

Click either cabinet to swap A ↔ B · Reference height: 1402 mm (140.2 cm) · 1 mm = 0.40 px

Plan view — footprint at true scale

front wall
A1508 cm²323 mm467 mm
B4044 cm²625 mm647 mm
0 mm100 mm30 mm

A shelf applies to bookshelf speakers only — one of these stands on the floor.

Seen from above, both pushed back to the same front wall — the wall behind the speakers. Only height, width and depth are published, so each cabinet is drawn as a rectangle: this is the surface a speaker reserves, not its exact outline. A curved or tapered cabinet takes a little less. How far a speaker should sit from the wall is yours to set: makers rarely publish it, and the ones that do disagree by design.

Performance — where each one sits in the catalog

BassTrebleSensitivityEasy loadCone area
Bass reachTreble reachSensitivityEasy loadCone area
Reference 5 Meta40 Hz35 kHz88 dB4 Ω983 cm²
La Scala AL640 Hz19 kHz103 dB8 Ω756 cm²
Median32 Hz30 kHz90 dB6 Ω654 cm²
How to read this chart

Each axis spans the range the 648 floorstanders in the catalog actually cover, so equal distance means equal difference — and for cone area and the two frequencies, which are read as ratios, equal distance means equal ratio. The dashed inner ring is where the scale starts, not zero. Ranked within a class because a bookshelf measured against floorstanders is feeble on every axis for the single reason that it is a bookshelf. Cone area is summed from the drive units — no maker publishes it. Bass and treble reach are quoted to different tolerances and only 56% of the catalog says which, so read those two axes as approximate. The grey outline is the median of the pair's own class, the 600 passive floorstanders — same type, same side of the active/passive line, which matters because the two halves are not the same product: the median active bookshelf carries 155 cm² of cone against the passive median's 219. Median rather than mean, because a handful of very large cabinets would drag a mean above most of the class it claims to describe.

KEF Reference 5 MetavsKlipsch La Scala AL6

The KEF Reference 5 Meta stands 140.2 cm tall — about 40.8 cm more than the Klipsch La Scala AL6 at 99.4 cm. On footprint the Klipsch La Scala AL6 is the wider cabinet (62.5 cm versus 32.3 cm). At 103 dB against 88 dB, the Klipsch La Scala AL6 is the easier load to drive and plays louder from the same amplifier. Low frequencies come from a 165 mm cone on the KEF Reference 5 Meta and a 305 mm cone on the Klipsch La Scala AL6. Both land in a similar price bracket, around $18,748 a pair.

Specifications

AB
ManufacturerKEFKlipsch
ModelReference 5 MetaLa Scala AL6
HiFi ladder position#574 of 648 floorstander#132 of 648 floorstander
Height1402 mm994 mm
Width323 mm625 mm
Depth467 mm647 mm
Footprint1508 cm²4044 cm²
Space taken211.5 L401.9 L
Weight60.2 kg93 kg
Enclosurebass-reflex-rear—
Drivers1× 25 mm tweeter (MAT aluminium dome), 1× 125 mm midrange (aluminium cone), 4× 165 mm woofer (aluminium cone)1× 25 mm tweeter (K-771 compression diaphragm), 1× 51 mm midrange (K-933-HP compression diaphragm), 1× 305 mm woofer (K-28 fiber-composite cone)
Crossover frequency450 / 2100 Hz425 / 2900 Hz
Frequency — low40 Hz40 Hz
Frequency — high35000 Hz19000 Hz
Sensitivity88 dB103 dB
Impedance4 Ω8 Ω
Recommended amp50–400 W—
MAP (USD)$19,998 / pair$17,498 / pair
Where to buyCheck availability ↗Check availability ↗
Brand websiteinternational.kef.com ↗klipsch.com ↗
Product pageOpen product page ↗Open product page ↗

Larger value highlighted in green. For low-frequency extension, lower Hz = greater bass reach, so the deeper side is highlighted.