TrueScaleAudio

Compare speakers at true scale

Pick two speakers and see them side by side at their real-world size.

Speaker A
Speaker B
References

Front view — side by side at true scale

AKlipsch RP-500M IIBPolk Reserve R200
Klipsch RP-500M II front view
Polk Reserve R200 front view

Click either cabinet to swap A ↔ B · Reference height: 359 mm (35.9 cm) · 1 mm = 1.56 px

Plan view — footprint at true scale

front wall
A462 cm²171 mm270 mm
B687 cm²194 mm354 mm
0 mm100 mm30 mm
150 mm500 mm300 mm

Seen from above, both pushed back to the same front wall — the wall behind the speakers. Only height, width and depth are published, so each cabinet is drawn as a rectangle: this is the surface a speaker reserves, not its exact outline. A curved or tapered cabinet takes a little less. How far a speaker should sit from the wall is yours to set: makers rarely publish it, and the ones that do disagree by design.

Performance — where each one sits in the catalog

BassTrebleSensitivityEasy loadCone area
Bass reachTreble reachSensitivityEasy loadCone area
RP-500M II50 Hz25 kHz92 dB8 Ω144 cm²
Reserve R20051 Hz38 kHz86 dB4 Ω219 cm²
Median45 Hz25 kHz87 dB6 Ω219 cm²
How to read this chart

Each axis spans the range the 470 bookshelves in the catalog actually cover, so equal distance means equal difference — and for cone area and the two frequencies, which are read as ratios, equal distance means equal ratio. The dashed inner ring is where the scale starts, not zero. Ranked within a class because a bookshelf measured against floorstanders is feeble on every axis for the single reason that it is a bookshelf. Cone area is summed from the drive units — no maker publishes it. Bass and treble reach are quoted to different tolerances and only 56% of the catalog says which, so read those two axes as approximate. The grey outline is the median of the pair's own class, the 385 passive bookshelves — same type, same side of the active/passive line, which matters because the two halves are not the same product: the median active bookshelf carries 155 cm² of cone against the passive median's 219. Median rather than mean, because a handful of very large cabinets would drag a mean above most of the class it claims to describe.

Klipsch RP-500M IIvsPolk Reserve R200

The Polk Reserve R200 stands 35.9 cm tall — about 1.5 cm more than the Klipsch RP-500M II at 34.4 cm. On footprint the Polk Reserve R200 is the wider cabinet (19.4 cm versus 17.1 cm). At 92 dB against 86 dB, the Klipsch RP-500M II is the easier load to drive and plays louder from the same amplifier. Low frequencies come from a 133 mm cone on the Klipsch RP-500M II and a 165 mm cone on the Polk Reserve R200. On price, the Polk Reserve R200 sits higher — about $749 a pair against $549 for the Klipsch RP-500M II.

Specifications

AB
ManufacturerKlipschPolk
ModelRP-500M IIReserve R200
HiFi ladder position#193 of 470 bookshelf#230 of 470 bookshelf
Height344 mm359 mm
Width171 mm194 mm
Depth270 mm354 mm
Footprint462 cm²687 cm²
Space taken15.9 L24.7 L
Weight5.95 kg8.7 kg
Enclosurebass-reflex-rearbass-reflex-rear
Drivers1× 25 mm tweeter (titanium LTS dome), 1× 133 mm mid-bass (Cerametallic cone)1× 25 mm tweeter (Pinnacle ring radiator), 1× 165 mm mid-bass (Turbine cone)
Crossover frequency1530 Hz3000 Hz
Frequency — low50 Hz51 Hz
Frequency — high25000 Hz38000 Hz
Sensitivity92 dB86 dB
Impedance8 Ω4 Ω
Recommended amp—30–200 W
MAP (USD)$549 / pair$749 / pair
Where to buyCheck on Amazon ↗Check on Amazon ↗
Brand websiteklipsch.com ↗polkaudio.com ↗
Product pageOpen product page ↗Open product page ↗

Larger value highlighted in green. For low-frequency extension, lower Hz = greater bass reach, so the deeper side is highlighted.