TrueScaleAudio

Compare speakers at true scale

Pick two speakers and see them side by side at their real-world size.

Speaker A

Stands apply to bookshelves only

Speaker B

Stands apply to bookshelves only

References

Front view — side by side at true scale

ADali Rubicon 6BKlipsch RP-6000F II
Dali Rubicon 6 front view
Klipsch RP-6000F II front view

Click either cabinet to swap A ↔ B · Reference height: 1006 mm (100.6 cm) · 1 mm = 0.56 px

Plan view — footprint at true scale

front wall
A760 cm²200 mm380 mm
B1075 cm²241 mm446 mm
0 mm100 mm30 mm

A shelf applies to bookshelf speakers only — one of these stands on the floor.

Seen from above, both pushed back to the same front wall — the wall behind the speakers. Only height, width and depth are published, so each cabinet is drawn as a rectangle: this is the surface a speaker reserves, not its exact outline. A curved or tapered cabinet takes a little less. How far a speaker should sit from the wall is yours to set: makers rarely publish it, and the ones that do disagree by design.

Performance — where each one sits in the catalog

BassTrebleSensitivityEasy loadCone area
Bass reachTreble reachSensitivityEasy loadCone area
Rubicon 638 Hz34 kHz88.5 dB4 Ω450 cm²
RP-6000F II38 Hz25 kHz96 dB8 Ω433 cm²
Median32 Hz30 kHz90 dB6 Ω654 cm²
How to read this chart

Each axis spans the range the 648 floorstanders in the catalog actually cover, so equal distance means equal difference — and for cone area and the two frequencies, which are read as ratios, equal distance means equal ratio. The dashed inner ring is where the scale starts, not zero. Ranked within a class because a bookshelf measured against floorstanders is feeble on every axis for the single reason that it is a bookshelf. Cone area is summed from the drive units — no maker publishes it. Bass and treble reach are quoted to different tolerances and only 56% of the catalog says which, so read those two axes as approximate. The grey outline is the median of the pair's own class, the 600 passive floorstanders — same type, same side of the active/passive line, which matters because the two halves are not the same product: the median active bookshelf carries 155 cm² of cone against the passive median's 219. Median rather than mean, because a handful of very large cabinets would drag a mean above most of the class it claims to describe.

Dali Rubicon 6vsKlipsch RP-6000F II

The Klipsch RP-6000F II stands 100.6 cm tall — about 1.6 cm more than the Dali Rubicon 6 at 99.0 cm. On footprint the Klipsch RP-6000F II is the wider cabinet (24.1 cm versus 20.0 cm). At 96 dB against 88.5 dB, the Klipsch RP-6000F II is the easier load to drive and plays louder from the same amplifier. On price, the Dali Rubicon 6 sits higher — about $4,999 a pair against $449 for the Klipsch RP-6000F II.

Specifications

AB
ManufacturerDaliKlipsch
ModelRubicon 6RP-6000F II
HiFi ladder position#127 of 648 floorstander#157 of 648 floorstander
Height990 mm1006 mm
Width200 mm241 mm
Depth380 mm446 mm
Footprint760 cm²1075 cm²
Space taken75.2 L108.1 L
Weight20.2 kg22.4 kg
Enclosurebass-reflex-rearbass-reflex-rear
Drivers1× 45 mm super-tweeter (ribbon), 1× 29 mm tweeter (soft textile dome), 2× 165 mm mid-bass (wood-fibre cone)1× 25 mm tweeter (titanium LTS dome), 2× 165 mm woofer (Cerametallic cone)
Crossover frequency800 / 2600 / 14000 Hz1770 Hz
Frequency — low38 Hz38 Hz
Frequency — high34000 Hz25000 Hz
Sensitivity88.5 dB96 dB
Impedance4 Ω8 Ω
Recommended amp40–200 W—
MAP (USD)$4,999 / pair$449 each
Where to buyCheck availability ↗Check on Amazon ↗
Brand websitedali-speakers.com ↗klipsch.com ↗
Product pageOpen product page ↗Open product page ↗

Larger value highlighted in green. For low-frequency extension, lower Hz = greater bass reach, so the deeper side is highlighted.