TrueScaleAudio

Compare speakers at true scale

Pick two speakers and see them side by side at their real-world size.

Speaker A
Speaker B
References

Front view — side by side at true scale

AKEF LS50 MetaBKlipsch RP-600M II
KEF LS50 Meta front view
Klipsch RP-600M II front view

Click either cabinet to swap A ↔ B · Reference height: 400 mm (40.0 cm) · 1 mm = 1.40 px

Plan view — footprint at true scale

front wall
A559 cm²199 mm281 mm
B660 cm²200 mm330 mm
0 mm100 mm30 mm
150 mm500 mm300 mm

Seen from above, both pushed back to the same front wall — the wall behind the speakers. Only height, width and depth are published, so each cabinet is drawn as a rectangle: this is the surface a speaker reserves, not its exact outline. A curved or tapered cabinet takes a little less. How far a speaker should sit from the wall is yours to set: makers rarely publish it, and the ones that do disagree by design.

Performance — where each one sits in the catalog

BassTrebleSensitivityEasy loadCone area
Bass reachTreble reachSensitivityEasy loadCone area
LS50 Meta79 Hz28 kHz85 dB8 Ω138 cm²
RP-600M II44 Hz25 kHz94.5 dB8 Ω219 cm²
Median45 Hz25 kHz87 dB6 Ω219 cm²
How to read this chart

Each axis spans the range the 470 bookshelves in the catalog actually cover, so equal distance means equal difference — and for cone area and the two frequencies, which are read as ratios, equal distance means equal ratio. The dashed inner ring is where the scale starts, not zero. Ranked within a class because a bookshelf measured against floorstanders is feeble on every axis for the single reason that it is a bookshelf. Cone area is summed from the drive units — no maker publishes it. Bass and treble reach are quoted to different tolerances and only 56% of the catalog says which, so read those two axes as approximate. The grey outline is the median of the pair's own class, the 385 passive bookshelves — same type, same side of the active/passive line, which matters because the two halves are not the same product: the median active bookshelf carries 155 cm² of cone against the passive median's 219. Median rather than mean, because a handful of very large cabinets would drag a mean above most of the class it claims to describe.

KEF LS50 MetavsKlipsch RP-600M II

The Klipsch RP-600M II stands 40.0 cm tall — about 9.8 cm more than the KEF LS50 Meta at 30.2 cm. At 94.5 dB against 85 dB, the Klipsch RP-600M II is the easier load to drive and plays louder from the same amplifier. The Klipsch RP-600M II reaches deeper in the bass, down to 44 Hz versus 79 Hz. Low frequencies come from a 130 mm cone on the KEF LS50 Meta and a 165 mm cone on the Klipsch RP-600M II. On price, the KEF LS50 Meta sits higher — about $1,599 a pair against $649 for the Klipsch RP-600M II.

Specifications

AB
ManufacturerKEFKlipsch
ModelLS50 MetaRP-600M II
HiFi ladder position#100 of 470 bookshelf#320 of 470 bookshelf
Height302 mm400 mm
Width199 mm200 mm
Depth281 mm330 mm
Footprint559 cm²660 cm²
Space taken16.9 L26.4 L
Weight7.8 kg8.67 kg
Enclosurebass-reflex-rearbass-reflex-rear
Drivers1× 25 mm tweeter (MAT aluminium dome), 1× 130 mm mid-bass (aluminium cone)1× 25 mm tweeter (titanium LTS dome), 1× 165 mm mid-bass (Cerametallic cone)
Crossover frequency2100 Hz1500 Hz
Frequency — low79 Hz44 Hz
Frequency — high28000 Hz25000 Hz
Sensitivity85 dB94.5 dB
Impedance8 Ω8 Ω
Recommended amp40–100 W—
MAP (USD)$1,599 / pair$649 / pair
Where to buyCheck on Amazon ↗Check on Amazon ↗
Brand websiteinternational.kef.com ↗klipsch.com ↗
Product pageOpen product page ↗Open product page ↗

Larger value highlighted in green. For low-frequency extension, lower Hz = greater bass reach, so the deeper side is highlighted.