TrueScaleAudio

Compare speakers at true scale

Pick two speakers and see them side by side at their real-world size.

Speaker A

Stands apply to bookshelves only

Speaker B

Stands apply to bookshelves only

References

Front view — side by side at true scale

AKEF Q11 MetaBKlipsch RP-8000F II
KEF Q11 Meta front view
Klipsch RP-8000F II front view

Click either cabinet to swap A ↔ B · Reference height: 1112 mm (111.2 cm) · 1 mm = 0.50 px

Plan view — footprint at true scale

front wall
A1197 cm²315 mm380 mm
B1301 cm²281 mm463 mm
0 mm100 mm30 mm

A shelf applies to bookshelf speakers only — one of these stands on the floor.

Seen from above, both pushed back to the same front wall — the wall behind the speakers. Only height, width and depth are published, so each cabinet is drawn as a rectangle: this is the surface a speaker reserves, not its exact outline. A curved or tapered cabinet takes a little less. How far a speaker should sit from the wall is yours to set: makers rarely publish it, and the ones that do disagree by design.

Performance — where each one sits in the catalog

BassTrebleSensitivityEasy loadCone area
Bass reachTreble reachSensitivityEasy loadCone area
Q11 Meta44 Hz20 kHz89 dB4 Ω723 cm²
RP-8000F II35 Hz25 kHz98 dB8 Ω652 cm²
Median32 Hz30 kHz90 dB6 Ω654 cm²
How to read this chart

Each axis spans the range the 648 floorstanders in the catalog actually cover, so equal distance means equal difference — and for cone area and the two frequencies, which are read as ratios, equal distance means equal ratio. The dashed inner ring is where the scale starts, not zero. Ranked within a class because a bookshelf measured against floorstanders is feeble on every axis for the single reason that it is a bookshelf. Cone area is summed from the drive units — no maker publishes it. Bass and treble reach are quoted to different tolerances and only 56% of the catalog says which, so read those two axes as approximate. The grey outline is the median of the pair's own class, the 600 passive floorstanders — same type, same side of the active/passive line, which matters because the two halves are not the same product: the median active bookshelf carries 155 cm² of cone against the passive median's 219. Median rather than mean, because a handful of very large cabinets would drag a mean above most of the class it claims to describe.

KEF Q11 MetavsKlipsch RP-8000F II

The KEF Q11 Meta stands 111.2 cm tall — about 1.7 cm more than the Klipsch RP-8000F II at 109.5 cm. On footprint the KEF Q11 Meta is the wider cabinet (31.5 cm versus 28.1 cm). At 98 dB against 89 dB, the Klipsch RP-8000F II is the easier load to drive and plays louder from the same amplifier. The Klipsch RP-8000F II reaches deeper in the bass, down to 35 Hz versus 44 Hz. Low frequencies come from a 165 mm cone on the KEF Q11 Meta and a 203 mm cone on the Klipsch RP-8000F II. On price, the KEF Q11 Meta sits higher — about $2,999 a pair against $599 for the Klipsch RP-8000F II.

Specifications

AB
ManufacturerKEFKlipsch
ModelQ11 MetaRP-8000F II
HiFi ladder position#335 of 648 floorstander#289 of 648 floorstander
Height1112 mm1095 mm
Width315 mm281 mm
Depth380 mm463 mm
Footprint1197 cm²1301 cm²
Space taken133.1 L142.5 L
Weight22.5 kg27.8 kg
Enclosurebass-reflex-rearbass-reflex-rear
Drivers1× 19 mm tweeter (MAT aluminium dome), 1× 100 mm midrange (aluminium cone), 3× 165 mm woofer (hybrid aluminium cone)1× 25 mm tweeter (titanium LTS dome), 2× 203 mm woofer (Cerametallic cone)
Crossover frequency480 / 2700 Hz1630 Hz
Frequency — low44 Hz35 Hz
Frequency — high20000 Hz25000 Hz
Sensitivity89 dB98 dB
Impedance4 Ω8 Ω
Recommended amp15–225 W—
MAP (USD)$2,999 / pair$599 each
Where to buyCheck on Amazon ↗Check on Amazon ↗
Brand websiteinternational.kef.com ↗klipsch.com ↗
Product pageOpen product page ↗Open product page ↗

Larger value highlighted in green. For low-frequency extension, lower Hz = greater bass reach, so the deeper side is highlighted.