TrueScaleAudio

Compare speakers at true scale

Pick two speakers and see them side by side at their real-world size.

Speaker A

Stands apply to bookshelves only

Speaker B

Stands apply to bookshelves only

References

Front view — side by side at true scale

AKEF R5 MetaBKlipsch RP-8000F II
KEF R5 Meta front view
Klipsch RP-8000F II front view

Click either cabinet to swap A ↔ B · Reference height: 1095 mm (109.5 cm) · 1 mm = 0.51 px

Plan view — footprint at true scale

front wall
A925 cm²269 mm344 mm
B1301 cm²281 mm463 mm
0 mm100 mm30 mm

A shelf applies to bookshelf speakers only — one of these stands on the floor.

Seen from above, both pushed back to the same front wall — the wall behind the speakers. Only height, width and depth are published, so each cabinet is drawn as a rectangle: this is the surface a speaker reserves, not its exact outline. A curved or tapered cabinet takes a little less. How far a speaker should sit from the wall is yours to set: makers rarely publish it, and the ones that do disagree by design.

Performance — where each one sits in the catalog

BassTrebleSensitivityEasy loadCone area
Bass reachTreble reachSensitivityEasy loadCone area
R5 Meta52 Hz28 kHz87 dB4 Ω393 cm²
RP-8000F II35 Hz25 kHz98 dB8 Ω652 cm²
Median32 Hz30 kHz90 dB6 Ω654 cm²
How to read this chart

Each axis spans the range the 648 floorstanders in the catalog actually cover, so equal distance means equal difference — and for cone area and the two frequencies, which are read as ratios, equal distance means equal ratio. The dashed inner ring is where the scale starts, not zero. Ranked within a class because a bookshelf measured against floorstanders is feeble on every axis for the single reason that it is a bookshelf. Cone area is summed from the drive units — no maker publishes it. Bass and treble reach are quoted to different tolerances and only 56% of the catalog says which, so read those two axes as approximate. The grey outline is the median of the pair's own class, the 600 passive floorstanders — same type, same side of the active/passive line, which matters because the two halves are not the same product: the median active bookshelf carries 155 cm² of cone against the passive median's 219. Median rather than mean, because a handful of very large cabinets would drag a mean above most of the class it claims to describe.

KEF R5 MetavsKlipsch RP-8000F II

The Klipsch RP-8000F II stands 109.5 cm tall — about 2.3 cm more than the KEF R5 Meta at 107.2 cm. On footprint the Klipsch RP-8000F II is the wider cabinet (28.1 cm versus 26.9 cm). At 98 dB against 87 dB, the Klipsch RP-8000F II is the easier load to drive and plays louder from the same amplifier. The Klipsch RP-8000F II reaches deeper in the bass, down to 35 Hz versus 52 Hz. Low frequencies come from a 130 mm cone on the KEF R5 Meta and a 203 mm cone on the Klipsch RP-8000F II. On price, the KEF R5 Meta sits higher — about $5,999 a pair against $599 for the Klipsch RP-8000F II.

Specifications

AB
ManufacturerKEFKlipsch
ModelR5 MetaRP-8000F II
HiFi ladder position#262 of 648 floorstander#289 of 648 floorstander
Height1072 mm1095 mm
Width269 mm281 mm
Depth344 mm463 mm
Footprint925 cm²1301 cm²
Space taken99.2 L142.5 L
Weight24.5 kg27.8 kg
Enclosurebass-reflex-rearbass-reflex-rear
Drivers1× 25 mm tweeter (MAT aluminium dome), 1× 125 mm midrange (aluminium cone), 2× 130 mm woofer (hybrid aluminium cone)1× 25 mm tweeter (titanium LTS dome), 2× 203 mm woofer (Cerametallic cone)
Crossover frequency400 / 2700 Hz1630 Hz
Frequency — low52 Hz35 Hz
Frequency — high28000 Hz25000 Hz
Sensitivity87 dB98 dB
Impedance4 Ω8 Ω
Recommended amp15–200 W—
MAP (USD)$5,999 / pair$599 each
Where to buyCheck on Amazon ↗Check on Amazon ↗
Brand websiteinternational.kef.com ↗klipsch.com ↗
Product pageOpen product page ↗Open product page ↗

Larger value highlighted in green. For low-frequency extension, lower Hz = greater bass reach, so the deeper side is highlighted.