TrueScaleAudio

Compare speakers at true scale

Pick two speakers and see them side by side at their real-world size.

Speaker A

Stands apply to bookshelves only

Speaker B

Stands apply to bookshelves only

References

Front view — side by side at true scale

AKlipsch RP-6000F IIBMonitor Audio Gold 300
Klipsch RP-6000F II front view
Monitor Audio Gold 300 front view

Click either cabinet to swap A ↔ B · Reference height: 1098 mm (109.8 cm) · 1 mm = 0.51 px

Plan view — footprint at true scale

front wall
A1075 cm²241 mm446 mm
B1570 cm²339 mm463 mm
0 mm100 mm30 mm

A shelf applies to bookshelf speakers only — one of these stands on the floor.

Seen from above, both pushed back to the same front wall — the wall behind the speakers. Only height, width and depth are published, so each cabinet is drawn as a rectangle: this is the surface a speaker reserves, not its exact outline. A curved or tapered cabinet takes a little less. How far a speaker should sit from the wall is yours to set: makers rarely publish it, and the ones that do disagree by design.

Performance — where each one sits in the catalog

BassTrebleSensitivityEasy load
Bass reachTreble reachSensitivityEasy load
RP-6000F II38 Hz25 kHz96 dB8 Ω
Gold 30028 Hz60 kHz87 dB4 Ω
Median32 Hz30 kHz90 dB6 Ω
How to read this chart

Each axis spans the range the 648 floorstanders in the catalog actually cover, so equal distance means equal difference — and for cone area and the two frequencies, which are read as ratios, equal distance means equal ratio. The dashed inner ring is where the scale starts, not zero. Ranked within a class because a bookshelf measured against floorstanders is feeble on every axis for the single reason that it is a bookshelf. Cone area is summed from the drive units — no maker publishes it. Bass and treble reach are quoted to different tolerances and only 56% of the catalog says which, so read those two axes as approximate. The grey outline is the median of the pair's own class, the 600 passive floorstanders — same type, same side of the active/passive line, which matters because the two halves are not the same product: the median active bookshelf carries 155 cm² of cone against the passive median's 219. Median rather than mean, because a handful of very large cabinets would drag a mean above most of the class it claims to describe. Not shown: Cone area — published by only one of the two. An outline reaching one more vertex than its neighbour reads as the bigger speaker when the only difference is which maker filled in a spec sheet. The figure is still in the table below.

Klipsch RP-6000F IIvsMonitor Audio Gold 300

The Monitor Audio Gold 300 stands 109.8 cm tall — about 9.2 cm more than the Klipsch RP-6000F II at 100.6 cm. On footprint the Monitor Audio Gold 300 is the wider cabinet (33.9 cm versus 24.1 cm). At 96 dB against 87 dB, the Klipsch RP-6000F II is the easier load to drive and plays louder from the same amplifier. The Monitor Audio Gold 300 reaches deeper in the bass, down to 28 Hz versus 38 Hz. Low frequencies come from a 165 mm cone on the Klipsch RP-6000F II and a 152 mm cone on the Monitor Audio Gold 300. On price, the Monitor Audio Gold 300 sits higher — about $6,199 a pair against $449 for the Klipsch RP-6000F II.

Specifications

AB
ManufacturerKlipschMonitor Audio
ModelRP-6000F IIGold 300 6G
HiFi ladder position#157 of 648 floorstander#295 of 648 floorstander
Height1006 mm1098 mm
Width241 mm339 mm
Depth446 mm463 mm
Footprint1075 cm²1570 cm²
Space taken108.1 L172.3 L
Weight22.4 kg21.2 kg
Enclosurebass-reflex-rearbass-reflex-rear
Drivers1× 25 mm tweeter (titanium LTS dome), 2× 165 mm woofer (Cerametallic cone)1× tweeter (MPD III (Air Motion Transformer)), 1× 76 mm midrange (HDT C-CAM), 2× 152 mm woofer (HDT C-CAM)
Crossover frequency1770 Hz800 / 2700 Hz
Frequency — low38 Hz28 Hz
Frequency — high25000 Hz60000 Hz
Sensitivity96 dB87 dB
Impedance8 Ω4 Ω
Recommended amp—130–500 W
MAP (USD)$449 each$6,199 / pair
Where to buyCheck on Amazon ↗Check availability ↗
Brand websiteklipsch.com ↗monitoraudio.com ↗
Product pageOpen product page ↗Open product page ↗

Larger value highlighted in green. For low-frequency extension, lower Hz = greater bass reach, so the deeper side is highlighted.