TrueScaleAudio

Compare speakers at true scale

Pick two speakers and see them side by side at their real-world size.

Speaker A
Speaker B
References

Front view — side by side at true scale

AKlipsch RP-600M IIBPolk Reserve R200
Klipsch RP-600M II front view
Polk Reserve R200 front view

Click either cabinet to swap A ↔ B · Reference height: 400 mm (40.0 cm) · 1 mm = 1.40 px

Plan view — footprint at true scale

front wall
A660 cm²200 mm330 mm
B687 cm²194 mm354 mm
0 mm100 mm30 mm
150 mm500 mm300 mm

Seen from above, both pushed back to the same front wall — the wall behind the speakers. Only height, width and depth are published, so each cabinet is drawn as a rectangle: this is the surface a speaker reserves, not its exact outline. A curved or tapered cabinet takes a little less. How far a speaker should sit from the wall is yours to set: makers rarely publish it, and the ones that do disagree by design.

Performance — where each one sits in the catalog

BassTrebleSensitivityEasy loadCone area
Bass reachTreble reachSensitivityEasy loadCone area
RP-600M II44 Hz25 kHz94.5 dB8 Ω219 cm²
Reserve R20051 Hz38 kHz86 dB4 Ω219 cm²
Median45 Hz25 kHz87 dB6 Ω219 cm²
How to read this chart

Each axis spans the range the 470 bookshelves in the catalog actually cover, so equal distance means equal difference — and for cone area and the two frequencies, which are read as ratios, equal distance means equal ratio. The dashed inner ring is where the scale starts, not zero. Ranked within a class because a bookshelf measured against floorstanders is feeble on every axis for the single reason that it is a bookshelf. Cone area is summed from the drive units — no maker publishes it. Bass and treble reach are quoted to different tolerances and only 56% of the catalog says which, so read those two axes as approximate. The grey outline is the median of the pair's own class, the 385 passive bookshelves — same type, same side of the active/passive line, which matters because the two halves are not the same product: the median active bookshelf carries 155 cm² of cone against the passive median's 219. Median rather than mean, because a handful of very large cabinets would drag a mean above most of the class it claims to describe.

Klipsch RP-600M IIvsPolk Reserve R200

The Klipsch RP-600M II stands 40.0 cm tall — about 4.1 cm more than the Polk Reserve R200 at 35.9 cm. At 94.5 dB against 86 dB, the Klipsch RP-600M II is the easier load to drive and plays louder from the same amplifier. The Klipsch RP-600M II reaches deeper in the bass, down to 44 Hz versus 51 Hz. On price, the Polk Reserve R200 sits higher — about $749 a pair against $649 for the Klipsch RP-600M II.

Specifications

AB
ManufacturerKlipschPolk
ModelRP-600M IIReserve R200
HiFi ladder position#320 of 470 bookshelf#230 of 470 bookshelf
Height400 mm359 mm
Width200 mm194 mm
Depth330 mm354 mm
Footprint660 cm²687 cm²
Space taken26.4 L24.7 L
Weight8.67 kg8.7 kg
Enclosurebass-reflex-rearbass-reflex-rear
Drivers1× 25 mm tweeter (titanium LTS dome), 1× 165 mm mid-bass (Cerametallic cone)1× 25 mm tweeter (Pinnacle ring radiator), 1× 165 mm mid-bass (Turbine cone)
Crossover frequency1500 Hz3000 Hz
Frequency — low44 Hz51 Hz
Frequency — high25000 Hz38000 Hz
Sensitivity94.5 dB86 dB
Impedance8 Ω4 Ω
Recommended amp—30–200 W
MAP (USD)$649 / pair$749 / pair
Where to buyCheck on Amazon ↗Check on Amazon ↗
Brand websiteklipsch.com ↗polkaudio.com ↗
Product pageOpen product page ↗Open product page ↗

Larger value highlighted in green. For low-frequency extension, lower Hz = greater bass reach, so the deeper side is highlighted.