TrueScaleAudio

Compare speakers at true scale

Pick two speakers and see them side by side at their real-world size.

Speaker A

Stands apply to bookshelves only

Speaker B

Stands apply to bookshelves only

References

Front view — side by side at true scale

AKlipsch RP-8000F IIBPolk Reserve R700
Klipsch RP-8000F II front view
Polk Reserve R700 front view

Click either cabinet to swap A ↔ B · Reference height: 1144 mm (114.4 cm) · 1 mm = 0.49 px

Plan view — footprint at true scale

front wall
A1301 cm²281 mm463 mm
B1404 cm²328 mm428 mm
0 mm100 mm30 mm

A shelf applies to bookshelf speakers only — one of these stands on the floor.

Seen from above, both pushed back to the same front wall — the wall behind the speakers. Only height, width and depth are published, so each cabinet is drawn as a rectangle: this is the surface a speaker reserves, not its exact outline. A curved or tapered cabinet takes a little less. How far a speaker should sit from the wall is yours to set: makers rarely publish it, and the ones that do disagree by design.

Performance — where each one sits in the catalog

BassTrebleSensitivityEasy loadCone area
Bass reachTreble reachSensitivityEasy loadCone area
RP-8000F II35 Hz25 kHz98 dB8 Ω652 cm²
Reserve R70038 Hz38 kHz88 dB4 Ω866 cm²
Median32 Hz30 kHz90 dB6 Ω654 cm²
How to read this chart

Each axis spans the range the 648 floorstanders in the catalog actually cover, so equal distance means equal difference — and for cone area and the two frequencies, which are read as ratios, equal distance means equal ratio. The dashed inner ring is where the scale starts, not zero. Ranked within a class because a bookshelf measured against floorstanders is feeble on every axis for the single reason that it is a bookshelf. Cone area is summed from the drive units — no maker publishes it. Bass and treble reach are quoted to different tolerances and only 56% of the catalog says which, so read those two axes as approximate. The grey outline is the median of the pair's own class, the 600 passive floorstanders — same type, same side of the active/passive line, which matters because the two halves are not the same product: the median active bookshelf carries 155 cm² of cone against the passive median's 219. Median rather than mean, because a handful of very large cabinets would drag a mean above most of the class it claims to describe.

Klipsch RP-8000F IIvsPolk Reserve R700

The Polk Reserve R700 stands 114.4 cm tall — about 4.9 cm more than the Klipsch RP-8000F II at 109.5 cm. On footprint the Polk Reserve R700 is the wider cabinet (32.8 cm versus 28.1 cm). At 98 dB against 88 dB, the Klipsch RP-8000F II is the easier load to drive and plays louder from the same amplifier. The Klipsch RP-8000F II reaches deeper in the bass, down to 35 Hz versus 38 Hz. The Klipsch RP-8000F II is rear-ported and the Polk Reserve R700 is down-firing ported. On price, the Polk Reserve R700 sits higher — about $1,499 a pair against $599 for the Klipsch RP-8000F II.

Specifications

AB
ManufacturerKlipschPolk
ModelRP-8000F IIReserve R700
HiFi ladder position#289 of 648 floorstander#382 of 648 floorstander
Height1095 mm1144 mm
Width281 mm328 mm
Depth463 mm428 mm
Footprint1301 cm²1404 cm²
Space taken142.5 L160.6 L
Weight27.8 kg35.9 kg
Enclosurebass-reflex-rearbass-reflex-down
Drivers1× 25 mm tweeter (titanium LTS dome), 2× 203 mm woofer (Cerametallic cone)1× 25 mm tweeter (Pinnacle ring radiator), 1× 165 mm midrange (Turbine cone), 2× 203 mm woofer (polypropylene cone)
Crossover frequency1630 Hz350 / 2700 Hz
Frequency — low35 Hz38 Hz
Frequency — high25000 Hz38000 Hz
Sensitivity98 dB88 dB
Impedance8 Ω4 Ω
Recommended amp—50–300 W
MAP (USD)$599 each$1,499 each
Where to buyCheck on Amazon ↗Check on Amazon ↗
Brand websiteklipsch.com ↗polkaudio.com ↗
Product pageOpen product page ↗Open product page ↗

Larger value highlighted in green. For low-frequency extension, lower Hz = greater bass reach, so the deeper side is highlighted.